Changing the cross-section of a hollow part
The starting tube is called the blank. The two die halves enclose a cavity shaped to the outside of the part. A straight blank can go directly into the tool; for a curved part, the blank is generally bent close to its intended centerline first. End punches seal the tube, and a passage through the tooling admits water or another forming fluid. As the pressure rises, the wall expands where there is room in the die. It can spread into a wide section or grow into a branch pocket. Where it has already met the die surface, outward movement is restrained.
Below yield, the metal springs back when the load is removed. Once it yields, some deformation is permanent. The machine releases the pressure and drains the fluid before the die opens. There may be a little springback, but the part retains its basic shape. What the die prescribes is the outside profile, not the thickness of the wall. Two parts can fill the same die and have different corner thicknesses: one received stock from the adjacent tube, while the other reached the corner largely by stretching the metal already there.
What carries the load: tube wall, end punches and press
Pressure puts the wall in circumferential tension. For an unsupported section of thin tube that is still close to a straight circular cylinder, the thin-cylinder approximation gives the hoop stress as σθ ≈ pD/(2t). Here p is the pressure difference across the wall, D is the current mean diameter and t is the current wall thickness. As the diameter grows and the wall thins, hoop stress can continue to rise even if the pressure holds steady. This helps explain why an already thin region can thin further. A branch intersection or a corner in contact with the die requires a different stress analysis.
Axial feed brings more metal into the expanding region. The volume of metal changes very little during plastic deformation. If a short length of tube supplies all the material for an increase in surface area, its wall has to thin. Advancing the end punches along the tube axis allows adjacent stock to share that deformation. A small expansion may need only a seal at each end. For a deep branch or a large change of section, the decisive question is often how much stock can reach the feature, not how much more pressure the pump can deliver.
Clamping and sealing react to the same pressure in different directions. Pressure in the tube produces a force tending to separate the dies. It also acts on each closed end and tries to drive the punch out. The press resists the separating force. The end actuator must resist the end thrust, maintain its seal and, when the process calls for feed, still have enough force to advance the blank. Press tonnage, fluid pressure and punch force therefore describe different duties.
Press capacity, pressure control and die geometry
A typical installation pairs a clamping press and forming die with a pressure intensifier, end punches and a controller. The intensifier supplies forming pressure. To estimate how much of that pressure the press must resist, consider the pressurized area projected onto the die parting plane. In a simplified example, 50 MPa acting over 100 cm² produces a separating force of about 500 kN. Double the projected area and the force doubles without any change in fluid pressure. A wide, long part may need a large press even when the material itself expands readily. The design of a North Carolina State University hydroforming rig treats closing, end sealing and pressurization as distinct requirements.
The separating force also changes during the stroke. Little is needed to resist pressure during filling; the peak may come late, when the wall is being calibrated into a tight radius. One variable-clamping design raises the clamping load as internal pressure rises. It holds the die closed at high pressure without applying that peak load through the low-pressure part of the cycle. This changes how the press is loaded. The shape of the die still governs how stock reaches the feature.
Consider a round tube expanding into a rectangular cavity. The wall meets the flats before it reaches the corners. Metal already touching a flat must slide against the tooling for more stock to reach a corner. An abrupt transition and a tight corner can leave a small area to take much of the remaining stretch. Easing the transition, preforming the blank closer to the required profile or dividing a large expansion into stages can address that difficulty more directly than specifying a larger press.
Material condition, weld position and the history of the blank
Outside diameter and wall thickness tell us how much metal is available. They say much less about how far it can deform. Yield strength is the stress at which permanent deformation begins; ductility describes how much deformation a material can take before fracture. Higher strength does not make a deep branch easier to form. A study of 6061 aluminum tubing compared as-extruded, fully annealed and T6 material in tests spanning 25 to 300 °C. In those tests the fully annealed tube was more formable than the as-extruded stock. Alloy designation, temper and forming temperature answer three different questions.
The choice between welded and seamless stock depends partly on where the expansion will take place. In longitudinally welded tube, the weld region may deform differently from the parent metal. Seamless stock has no longitudinal weld, but a tight bend or a large expansion can still thin its wall. In a hydraulic bulge test on welded steel tube, a free length of one tube diameter produced a fracture in the parent metal beside the weld. At free lengths of two and three diameters, fracture occurred on the opposite side. Changing the constraint was enough to move the failure even though the material had not changed.
A curved blank arrives in the hydroforming die with some of its forming capacity already spent. The outside of a pre-bend has stretched and may already be thin. A large expansion at that location asks the same material to stretch a second time. The University of Waterloo's bending and hydroforming work measured both thickness and strain after bending and again after hydroforming. For a curved part, changing the bend radius, preform section or weld orientation may be more useful than raising the final pressure.
The loading path: pressure and end feed through the cycle
Forming pressure and end feed each have a history. When does pressure build? At what point do the punches move, and how much stock do they deliver during expansion? Together, these histories are the loading path. Stock pushed in while the tube can still slide is not equivalent to the same feed applied after pressure has locked a long section against the die. Two paths can finish at the same pressure and punch position and still produce an intact part in one case and a split in the other.
A copper tee makes the distinction visible. The starting tube is straight; a side pocket in the die defines the branch. Pressure raises a closed bulge in the wall. The advancing punches feed surrounding stock toward it as it grows. A taller branch needs more surface area, and stretching the original patch alone soon costs wall thickness. How much punch travel reaches the branch as metal flow depends on friction along the intervening tube. The closed tip is opened after forming to give the finished tee a through passage. In tests on copper tees and crosses at Dublin City University, the researchers compared branch height and wall-thickness distribution. The height alone would not reveal how much wall remained.
A useful way to read a cycle is to distinguish support, expansion and final calibration. Early pressure helps support the tube as axial compression builds. During expansion, stock has to arrive while it can still flow. Once most of the wall is in contact with the die, the remaining pressurization serves mainly to fill corners and local detail. The transition between these stages is specific to the part. An enlarged section halfway along a beam is a different distance from its source of material than a flare near the end of a tube.
Industrial applications: the purpose of the formed feature
Automotive structures and exhaust systems
For a body reinforcement or a subframe crossmember, the attraction is a continuous hollow member with a section that can vary along its length. It can widen at a mounting point and narrow where packaging space is tight. A tubular design may dispense with flanges and seam welds that would otherwise join two stamped shells; mounting brackets and assembly joints remain separate design features. An exhaust section serves a different purpose. Its ends must match adjacent pipes while its middle clears nearby components. Forming the transition in the tube can eliminate a separately fitted reducer. ShuiYiYuan's automotive applications distinguish exhaust parts from chassis and body structures.
An axle housing shows both the benefit and the cost of integrating parts. The conventional housing used seven stampings welded together. Making the housing from one tube required a large expansion in the middle of a long blank with relatively narrow ends. In Nippon Steel's prototype development, the starting steel tube had an outside diameter of 60.5 mm and a wall thickness of 2.8 mm. The team used moving dies and three hydroforming stages: expansion in different directions followed by final calibration. The circumference of the expanded section reached 2.8 times the starting circumference. Staging addressed a specific problem: end punches alone could not feed enough metal past the long contact region to the center of the housing. The team reported a weight saving of about 10% for the integrated prototype compared with the conventional housing.
Bellows for aircraft ducts and industrial piping
A structural beam is meant to resist deflection. A bellows is shaped precisely so that it can flex. Industrial pipework grows as it heats up, and adjacent sections of an aircraft bleed-air duct can move relative to each other. In hydraulically formed bellows, internal pressure first bulges a thin tube between rings of tooling. Axial tool movement brings the rings closer together and forms a convolution. Several convolutions can extend, compress or deflect while keeping the metal wall continuous. Witzenmann illustrates the forming operation in its bellows handbook and the resulting flexible joints in its aircraft ducting literature.
Refrigeration, plumbing and data-center cooling
A refrigeration tee needs a branch passage; a distribution manifold may instead need several shallow collars for ports to be opened and connected later. Separate branches must each be located on the main line before joining. Forming a branch or collar directly in the wall lets the die locate it relative to the main tube. ShuiYiYuan's liquid-cooling parts include stainless steel press-fit pipe components, stainless steel or copper manifold components and stainless steel line sections inside servers. Plumbing fixtures offer another division of labor: in a prototype faucet made from SUS 304 stainless tube, bending and hydroforming were combined to produce the tube's overall sweep and local profile.
Bicycle and motorcycle frame tubes
Frame tubes have to carry loads, fit the available space and meet neighboring tubes at suitable junctions. A constant round section is not always the best shape for all three jobs. Giant's aluminum frame process uses fluid pressure to shape tubing around the head tube and bottom bracket, then joins the individual tubes by welding. The KTM 85 SX chrome-moly steel frame likewise uses hydroformed tubing and robotic welding. Forming and welding are complementary here: one produces the local tube profile and the other assembles the load-bearing frame.
Mechanically lined pipe
Hydraulic expansion can also join two tubes without forming a new outside profile. In mechanically lined pipe, an outer steel pipe carries structural loads and a corrosion-resistant liner protects the bore. Pressure expands the liner, first closing its clearance to the outer pipe and then bringing the two walls into firm contact. Their different deformation and recovery can leave residual pressure at the interface after the forming fluid is released. In hydraulic-expansion trials on corrosion-resistant lined pipe, that residual contact pressure was of more interest than any change in outside diameter.
Defect control and the forming window
Pressure and feed can move a part toward opposite failure limits. Excess stock fed into a tube before pressure can support it puts the wall into lengthwise compression and can buckle it into wrinkles. If instead a region expands faster than stock can reach it, the wall stretches locally, thins and may split. Incomplete corner fill is different again: the wall can meet both die flats yet bridge their tight intersection with a larger radius. The visible defect matters because each points to a different stage of the operation.
| What the trial part shows | What distinguishes the cause |
|---|---|
| Wrinkles near the feed zone | Identify when they first appeared and compare feed at that stage with the available pressure support. A shallow wrinkle and a folded-over wall are different conditions. |
| A split at a bulge or outer bend | Map thickness on either side of the split and in adjacent material. Compare with the pre-bent blank to separate prior thinning from stretch added in the die. |
| Flats filled, corner bridged | Check the actual corner radius and remaining wall together. The distinction is between incomplete calibration and a radius that demands more deformation than the blank can sustain. |
For a particular blank and die, the pressure and feed combinations that fill the tool without harmful wrinkles or rupture constitute the forming window. A finished outline tells only part of the story. Experimental work on tube wrinkles shows that some shallow wrinkles can flatten later in the cycle, whereas a folded wrinkle can remain in the part. A sound-looking profile can also conceal a local neck: stretching concentrates in a narrow band and thickness drops rapidly. A forming limit diagram established for tube material helps identify this tensile instability. Wrinkling and corner fill need their own checks.
Extending the process and deciding when to use it
Temperature control and material redistribution address different limits. For some aluminum alloys, forming warm reduces resistance to deformation. But a tube that loses heat unevenly to the tooling may concentrate stretch in its hotter sections. In a warm-forming study on 6061 tube, a combined heating system improved temperature uniformity along the tube and produced more uniform bulging. The steel axle housing described earlier took a different route: multiple stages and moving dies redistributed stock without relying on elevated temperature.
Finite element simulation allows engineers to compare blank shapes, pre-bends and loading paths before cutting a trial die. The useful prediction is where the wall will stretch and whether strain will localize, not just whether the simulated part resembles the drawing. If a model reproduces the profile but puts the thinnest wall on the wrong side, it is not yet a sound basis for a thickness allowance. Measurements around the trial part, along with the positions of any wrinkles or fractures, are a stronger check than a profile overlay alone.
Start the process decision with the shape. Bending may be all a constant-diameter line needs to change direction. Two stamped shells remain a reasonable choice where the seam is accessible and easy to join. Hydroforming has a distinct purpose when one continuous tube needs to change section along its length, carry a side branch or replace several pieces previously welded together. Only then is it useful to compare the material condition, pre-bending, tooling, port cutting, assembly and production quantity. Those details determine which operations the new design eliminates and which demands it places on the forming step.